Arm Cortex-M4|Kinetis K40 100 MHz 32-bit MCUs

For best experience this site requires Javascript to be enabled. To enable on your browser, follow our accessibility instructions.

Click over video to play

The Kinetis^® K40 100 MHz MCU family provides advanced analog integration and serial communication for consumer, industrial, and medical applications.

Offers optimized low power and mixed signal analog integration
Includes a rich suite of analog, communication, timing and control peripherals to accommodate a wide range of requirements
Optimizes charging current/time for portable USB devices, enabling longer battery life
Shares the comprehensive enablement and scalability of the Kinetis portfolio

Data Sheet

Reference Manual

Product Details

Block Diagram

Kinetis K40 MCU Family Block Diagram

Get diagram PDF

Features

Ultra-Low-Power

10 low-power modes with power and clock gating for optimal peripheral activity and recovery times. Stop currents down to 2 µA, and run currents of <350 µA/MHz, with 4 µs wake-up from Stop mode
Full memory and analog operation down to 1.71 volts for extended battery life
Low-leakage wake-up unit with up to eight internal modules and 16 pins as wake-up sources in low-leakage stop (LLS)/very low-leakage stop (VLLS) modes
Low-power timer for continual system operation in reduced power state

Flash, SRAM and FlexMemory

128 KB - 512 KB flash. Fast access, high reliability with four-level security protection
32 KB-128 KB of SRAM
FlexMemory: 32 bytes-4KB of user-segmentable byte write/erase EEPROM for data tables/system data. EEPROM with over 10M cycles and flash with 70 µsec write time (brownouts without data loss/corruption). No user or system intervention to complete programming and erase functions and full operation down to 1.71 volts. In addition, upto 256 KB can be used for extra program code, data or EEPROM backup

Mixed-Signal Capability

Two high-speed 16-bit analog-to-digital converter (ADC) with configurable resolution. Single or differential output mode operation for improved noise rejection. 500 ns conversion time achievable with programmable delay block triggering
Up two 12-bit digital-to-analog converter (DAC) for analog waveform generation for audio applications
Three high-speed comparators providing fast and accurate motor over-current protection by driving PWMs to a safe state
Analog voltage reference provides an accurate reference to analog blocks, ADC and DAC, and replaces external voltage references to reduce system cost

Performance

Arm^® Cortex^®-M4 core with DSP, 100MHz clock, single cycle MAC, and single instruction multiple data (SIMD) extensions
16-channel DMA for peripheral and memory servicing with reduced CPU loading and faster system throughput
Cross bar switch enables concurrent multi-leader bus accesses, increasing bus bandwidth
Independent flash banks allow concurrent code execution and firmware updating with no performance degradation or complex coding routines

Timing and Control

Up to three FlexTimers with a total of 12 channels. Hardware dead-time insertion and quadrature decoding for motor control
Carrier modulator timer for infrared waveform generation in remote control applications
Four-channel 32-bit periodic interrupt timer provides time base for RTOS task scheduler or trigger source for ADC conversion and programmable delay block

Human-Machine Interface

Hardware touch-sensing interface with up to 16 inputs. Operates in all low power modes (minimum current adder when enabled). Hardware implementation avoids software polling method. High sensitivity level allows use of overlay surfaces upto 5 mm thick
Flexible, low-power LCD controller with up to 320 segments (40x8 or 44x4). LCD blink mode enables low average power while remaining in low-power mode. Segment fail detect guards against erroneous readouts and reduces LCD test costs. Frontplane/backplane reassignment provides pin-out flexibility easing PCB design and allows LCD configuration changes via firmware with no hardware re-work. Supports multiple 3 volts and 5 volts LCD panel sizes with fewer segments (pins) than competitive controllers and no external components. Unused LCD pins can be configured as other GPIO functions

Connectivity and Communications

USB 2.0 On-The-Go (full speed). Device charge detect optimizes charging current/time for portable USB devices enabling longer battery life. Low-voltage regulator supplies up to 120 mA off chip at 3.3V to power external components from 5V input
Up to six UARTs with IrDA support including one UART with ISO7816 smart card support. Variety of data size, format and transmission/reception settings supported for multiple industrial communication protocols
Inter-IC Sound (I²S) serial interface for audio system interfacing
Two CAN modules for industrial network bridging
Up to three DSPI and two I²C

Reliability, Safety and Security

Memory protection unit provides memory protection for all controllers on the cross bar switch, increasing software reliability
Cyclic redundancy check engine validates memory contents and communication data, increasing system reliability
Independent-clocked COP guards against clock skew or code runaway for fail-safe applications such as the IEC 60730 safety standard for household appliances
External watchdog monitor drives output pin to safe state external components if watchdog event occurs
This product is included in NXP^®.s product longevity program, with assured supply for a minimum of 10 years after launch

External Peripheral Support

FlexBus external bus interface provides interface options to memories and peripherals such as graphics displays. Supports up to 6 chip selects and 2GB addressable space
Secure digital host controller supports SD, SDIO, MMC or CE-ATA cards for in-application software upgrades, or media files.

MCUXpresso Software and Tools

Buy/Parametrics

‌ ‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌

Design Resources

Design Files

Quick reference to our design files types.

2 design files

Receive the full breakdown. See the product footprint and more in the eCad file.

Symbols and Footprints
Kinetis^® Symbols, Footprints and Models

INTERNALRev 1.0Nov 27, 2017 11:23:001 KBCAD-SYMBOLFOOTPRINTS

Download
Calculators
TFS FlexMem Endurance Calculator

ZIPRev vBeta025Aug 1, 2014 00:00:003.2 MBTFS_FLEXMEM_CALCULATOR

Account Required
DownloadToggle Dropdown
- Add to Queue
- Remove from Queue
- Recommended for large file sizes.
- View Queue

Hardware

Quick reference to our board types.

1-5 of 12 hardware offerings

Evaluation and Development Boards
Kinetis K40 100 MHz Low-Power MCU Tower System ModuleFeatured

TWR-K40D100M
Complete Solution
K60 3-Phase PMSM Sensorless Vector Control Reference Design

RD3PHASEPMSMSVCK60
Emulators, Probes, and Programmers
Universal Multilink Development Interface

UMultilink
Additional hardware available. View our featured partner solutions.
Emulators, Probes, and Programmers
MCU-Link Debug Probe

MCU-LINK
Emulators, Probes, and Programmers
Tracelink - Advance Trace Capture

TRACELINK
Emulators, Probes, and Programmers
LPC-Link2

OM13054
Emulators, Probes, and Programmers
Universal Multilink FX High-Speed Development Interface

U-MULTILINK-FX
Emulators, Probes, and Programmers
PEmicro Cyclone programmer

CYCLONE
Emulators, Probes, and Programmers
PEmicro Cyclone FX programmer

CYCLONE-FX
Evaluation and Development Boards
MPC560x Calibration, Debug and Interface Boards

MPC560xBOARDS
Evaluation and Development Boards
Ultra low-cost development tool for Kinetis MCUs

KWIKSTIK-K40
Evaluation and Development Boards
MCU-LINK-MR Debug Probe with USB-C, Serial and Mobile Robotics Interfaces

MCU-LINK-MR

Show All

1-5 of 8 hardware offerings

Evaluation and Development Boards
Mikromedia 7 Capacitive

Mikromedia 7 Capacitive is a compact development board designed as a complete solution for the rapid development of multimedia and GUI-centric applications. As a fully fu...

By MIKROE Gold Partner
Evaluation and Development Boards
Fusion for ARM v8

Fusion for ARM v8 offers universal support for ARM Cortex MO, M3, M4, and M7 Microcontrollers on one board. The development board is equipped with a wide range of superio...

By MIKROE Gold Partner
Evaluation and Development Boards
Fusion for Kinetis v8

Fusion for Kinetis v8 offers support for a variety of NXP's popular ARM Cortex-M4 Microcontrollers on one board. The development board is equipped with a wide range of su...

By MIKROE Gold Partner
Evaluation and Development Boards
Mikromedia 7 Capacitive FPI with bezel

Mikromedia 7 Capacitive FPI (FPI stands for Front Panel Integration) with bezel is a compact development board designed as a complete solution for the rapid development o...

By MIKROE Gold Partner
Test Accessories and Debugger
Flasher Compact

Flasher Compact is the compact twin to the Flasher PRO, primarily designed for installation into production rigs or automated test equipment (ATE) where production space ...

By SEGGER Microcontroller GmbH Gold Partner
Test Accessories and Debugger
J-Link PRO PoE

J-Link PRO PoE is SEGGER's specialized programming / debug probe for creating test farms. It can draw power via Ethernet and supplies power to the target either via d...

By SEGGER Microcontroller GmbH Gold Partner
Test Accessories and Debugger
CODEGRIP for ARM

CODEGRIP for ARM is a fast USB-C and WiFi programmer and hardware debugger. It supports ARM Cortex-M0, M3,M4 and M7 based MCUs. With a set of unique and innovative funct...

By MIKROE Gold Partner
Test Accessories and Debugger
I-jet

I-jet is a high-performing in-circuit debugging probe for ARM. It is capable of delivering power to the target board and measuring target power consumption. I-jet is full...

By IAR Platinum Partner