Design Files
Receive the full breakdown. See the product footprint and more in the eCad file.
NFC Cortex®-M0 All-in-One Microcontroller with Optional Contact Interface for Access Control
Please check the new online NFC Antenna Tool for tag and reader devices.
The PN7462 family consists of 32-bit Arm® Cortex®-M0-based NFC microcontrollers offering high performance and low power consumption. It has a simple instruction set and memory addressing along with a reduced code size compared to existing architectures. PN7462 family offers an all-in-one-solution, with features such as NFC, supporting all NFC Forum modes, microcontroller, optional contact smart card reader, and software in a single chip. It operates at CPU frequencies of up to 20 MHz.
See the main differences between our products in the table below.Product Details
Features
Integrated contact interface frontend
- Class A, B, and C cards can work on 1.8 V, 3 V, and 5 V supply
- Specific ISO UART, variable baud rate through frequency or division ratio programming, error management at character level for T = 0, and extra guard time register
- DC-to-DC converter for class A support starting at 3 V, and class B support starting at 2.7 V
- Thermal and short-circuit protection on contact cards
- Automatic activation and deactivation sequence, initiated by software or by hardware in case of short-circuiting, card removal, overheating, and VDD or VDD drop-out
- Enhanced ESD protection (< 12 kV)
- ISO/IEC 7816 compliant
- Compliance with EMV contact protocol specification
- Clock generation up to 13.56 MHz
- Synchronous card support
- Possibility to extend the number of contact interfaces, with the addition of slot extenders such as TDA8026
Integrated ISO/IEC 7816-3&4 UART interface
- Class A (5 V), class B (3 V), and class C (1.8 V) smart card supply
- Protection of smart card
- Three protected half-duplex bidirectional buffered I/O lines (C4, C7, and C8)
- Compliant with ISO/IEC 7816 and EMVCo standards
The PN7462 family offers the possibility to extend the number of contact interfaces available. It uses an I/O auxiliary interface to connect a slot extension (TDA8035 - 1 slot, TDA8020 - 2 slots, and TDA8026 - 5 slots)
Integrated contactless interface frontend
- High RF output power frontend IC for transfer speed up to 848 kbit/s
- NFC IP1 and NFC IP2 support
- Full NFC Forum tag support (type 1, type 2, type 3, type 4A, type 4B and type 5)
- P2P active and passive, target and initiator
- Card emulation ISO14443 type A
- ISO/IEC 14443 type A and type B
- MIFARE products using Crypto1
- ISO/IEC 15693, and ISO/IEC 18000-3 mode 3
- Low-power card detection
- Dynamic Power Control (DPC)
- Adaptive Wave Control (AWC)
- Adaptive Range Control (ARC)
- Compliance with EMV contactless protocol specification
Cortex-M0 microcontroller
- Processor core
- Arm® Cortex®: 32-bit M0 processor
- Built-in Nested Vectored Interrupt Controller (NVIC)
- Non-maskable interrupt
- 24-bit system tick timer
- Running frequency of up to 20 MHz
- Clock management to enable low power consumption
- Memory
- Flash: 160 kB / 80 kB
- SRAM: 12 kB
- EEPROM: 4 kB
- 40 kB boot ROM included, including USB mass storage primary bootloader for code download
- Debug option
- Serial Wire Debug (SWD) interface
- Peripherals
- Host interface:
- USB 2.0 full speed with USB 3.0 hub connection capability
- HSUART for serial communication, supporting standards speeds from 9600 bauds to 115200 bauds, and faster speeds up to 1.288 Mbit/s
- SPI with half-duplex and full duplex capability with speeds up to 7 Mbit/s
- I2C supporting standard mode, fast mode and high-speed mode with multiple address support
- Controller interface:
- SPI with half-duplex capability from 1 Mbit/s to 6.78 Mbit/s
- I2C supporting standard mode, fast mode, fast mode plus and clock stretching
- Up to 21 General-Purpose I/O (GPIO) with configurable pull-up/pull-down resistors
- GPIO1 to GPIO12 can be used as edge and level sensitive interrupt sources
- Power
- Two reduced power modes: standby mode and hard power-down mode
- Supports suspend mode for the USB host interface
- Processor wake-up from hard power-down mode, standby mode, suspend mode via host interface, GPIOs, RF field detection
- Integrated PMU to adjust internal regulators automatically, to minimize the power consumption during all possible power modes
- Power-on reset
- RF supply: external, or using an integrated LDO (TX LDO, configurable with 3 V, 3.3 V, 3.6 V, 4.5 V, and 4.75 V)
- Pad voltage supply: external 3.3 V or 1.8 V, or using an integrated LDO (3.3 V supply)
- Timers
- Four general-purpose timers
- Programmable Watchdog Timer (WDT)
- CRC coprocessor
- Random number generator
- Clocks
- Crystal oscillator at 27.12 MHz
- Dedicated PLL at 48 MHz for the USB
- Integrated HFO 20 MHz and LFO 365 kHz
- General
- HVQFN64 package
- VFBGA64 package
- Temperature range: -40 °C to +85 °C
Other Features
- Supported by the NFC Cockpit Configuration Tool
Comparison Table
| PN7462 Family | PN7412AU | PN7462AU | PN7362AU | PN7360AU | |||
|---|---|---|---|---|---|---|---|
| Item reference | PN7412AUHN | PN7462AUHN | PN7462AUEV | PN7362AUHN | PN7362AUEV | PN7360AUHN | PN7360AUEV |
| Package type | HVQFN64 | HVQFN64 | VFBGA64 | HVQFN64 | VFBGA64 | HVQFN64 | VFBGA64 |
| Contactless Interface | No | NFC Forum Compliant | |||||
| Available Flash Memory | 160 kB | 80kB | |||||
| General Purposes I/O | 12 up-to 21 | 14 up-to 21 | |||||
| Contact Interface | Class A, B, C | No | |||||
| ISO/IEC 7816- &: 4 UART | Yes | No | |||||
Buy/Parametrics
|
|
|
|
|
|
|
|---|---|---|---|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Documentation
Quick reference to our documentation types.
1-5 of 20 documents
-
Application Note
Crystal Oscillator Design Guide - Application notenew
-
Application Note
IFM L1 test tool for PN7462
-
Application Note
End of life TDA80xx migration path to active portfolio
-
Application Note
PN7462 family Antenna design guide
Design Resources
Hardware
Quick reference to our
board types.
1-5 of 8 hardware offerings
-
Evaluation and Development BoardsNFC Controller development kitFeatured
-
Evaluation and Development BoardsNFC Antenna Development KitFeatured
-
Reference Designi.MX RT Industrial Drive Development PlatformFeatured
-
Additional hardware available. View our featured partner solutions.
-
Complete SolutionPegoda Smart Card Reader Based on PN7642
-
Emulators, Probes, and ProgrammersUniversal Multilink Development Interface
Software
Quick reference to our software types.
1-5 of 6 software files
-
Configuration Tools
NFC Cockpit Configuration Tool for NFC ICs
-
Configuration Tools
NFC Antenna Design Hub
-
HMI Design Software
Online NFC Antenna Design Tool
-
Application Example Software
SCRTester including user manual
Note: For better experience, software downloads are recommended on desktop.
Engineering Services
To get further assistance directly from NXP, please see our Engineering Services.
1-5 of 17 engineering services
-
Independent Design House (IDH)
Engineering Services and Consulting
-
Independent Design House (IDH)
Hardware Design Services
-
Independent Design House (IDH)
NFC Charging Wireless System Design
-
Independent Design House (IDH)
NFC demonstrators
-
Independent Design House (IDH)
Hardware/Software development and testing
.svg)
To find additional partner offerings that support this product, visit our Partner Marketplace.