LPC80x 15 MHz|Arm Cortex-M0+|32-bit Microcontrollers (MCUs) | NXP Semiconductors

Automotive

Industrial

Consumer

Technologies

LPC800: 32-Bit Arm® Cortex®-M0+-Based Low-Cost MCU

LPC80X Active

Roll over image to zoom in

LPC80x is a cost-effective Arm Cortex-M0+ based 32-bit MCU family operating at CPU frequencies of up to 15 MHz. The LPC80x MCU family supports up to 32 KB of flash memory and up to 4 KB of SRAM.

This family features a power-optimized core, small footprint in popular packages, and level shifting options thanks to its separate power rails. The peripheral complement of the LPC80x includes a CRC engine, I²C-bus interfaces, up to two USARTs, one SPI interface, capacitive touch interface (cap touch), one multi-rate timer, self-wake-up timer, one general purpose 32-bit counter/timer, one 12-bit ADC, one 10-bit DAC, one analog comparator, function-configurable I/O ports through a switch matrix, an input pattern match engine, programmable logic unit (PLU), and up to 30 general-purpose I/O pins.

This device is fully supported by NXP’s MCUXpresso Software and Tools, a comprehensive and cohesive set of free software development tools for Kinetis, LPC and i.MX RT microcontrollers. MCUXpresso SDK also includes project files for Keil MDK and IAR EWARM.

Block Diagram

LPC80x MCU

LPC80x MCU
Get diagram PDF

Features

System

  • Arm Cortex-M0+ processor (revision r0p1), running at frequencies of up to 15 MHz with single-cycle multiplier and fast single-cycle I/O port
  • Arm Cortex-M0+ built-in Nested Vectored Interrupt Controller (NVIC)
  • System tick timer
  • AHB multilayer matrix
  • Serial Wire Debug (SWD) with four break points and two watchpoints. JTAG boundary scan (BSDL) supported

Memory

  • Up to 32 KB on-chip flash programming memory
  • Code Read Protection (CRP)
  • Up to 4 KB SRAM
  • Dual I/O power (LPC802M011JDH20, LPC804M111JDH24):
    • Independent supplies on each package side permitting level-shifting signals from one off-chip voltage domain to another and/or interfacing directly to off-chip peripherals operating at different supply levels

ROM API support

  • Bootloader
  • Supports Flash In-Application Programming (IAP)
  • Supports In-System Programming (ISP) through USART
  • On-chip ROM APIs for integer divide
  • Free Running Oscillator (FRO) API

Digital peripherals

  • High-speed GPIO interface connected to the Arm Cortex-M0+ I/O bus with up to 30 General-Purpose I/O (GPIO) pins with configurable pull-up/pull-down resistors, programmable open-drain mode, and input inverter. GPIO direction control supports independent set/clear/toggle of individual bits
  • High-current source output driver (20 mA) on three pins
  • GPIO interrupt generation capability with a boolean pattern-matching feature on eight GPIO inputs. (LPC804)
  • Switch matrix for flexible configuration of each I/O pin function
  • CRC engine
  • Capacitive Touch Interface. (LPC804)
  • Programmable Logic Unit (PLU) to create small combinatorial and/or sequential logic networks including simple state machines. (LPC804)

Timers

  • One 32-bit general purpose counter/timer, with four match outputs and three capture inputs. Supports PWM mode, and external count
  • Multi-Rate Timer (MRT) for repetitive interrupt generation at up to four programmable, fixed rates
  • Self-Wake-up Timer (WKT) clocked from either Free Running Oscillator (FRO), a low-power, low-frequency internal oscillator, or an external clock input
  • Windowed Watchdog timer (WWDT)

Analog peripherals

  • One 12-bit ADC with up to 12 input channels with multiple internal and external trigger inputs and with sample rates of up to 480 Ksamples/s. The ADC supports two independent conversion sequences
  • Comparator with five input pins and external or internal reference voltage
  • One 10-bit DAC. (LPC804)

Serial peripherals

  • Two USART interfaces with pin functions assigned through the switch matrix and one fractional baud rate generators
  • One SPI controllers with pin functions assigned through the switch matrix
  • Up to two I²C-bus interfaces. It supports data rates up to 400 kbit/s on standard digital
  • pins

Clock generation

  • Free Running Oscillator (FRO). This oscillator provides a selectable 9 MHz, 12 MHz and 15 MHz outputs that can be used as a system clock. The FRO is trimmed to ±1 % accuracy over the entire voltage and temperature range of 0 °C to 70 °C
  • 1 MHz low power oscillator can be used as a clock source
  • Clock output function with divider that can reflect all internal clock sources

Power control

  • Reduced power modes: sleep mode, deep-sleep mode, power-down mode, and deep power-down mode
  • Wake-up from deep-sleep and power-down modes of activity on USART, SPI, and I²C peripherals
  • Wake-up from deep power-down mode on multiple pins
  • Timer-controlled self-wake-up from sleep, deep-sleep, and power-down modes
  • Power-On Reset (POR)
  • Brownout detect (BOD)

Additional features

  • Unique device serial number for identification
  • Single or dual power supplies (1.71 V to 3.6 V)
  • Operating temperature range -40 °C to +105 °C
  • Available in TSSOP16, TSSOP20, TSSOP24 and HVQFN33 packages
  • Supported by MCUXpresso SDK, IDE and Config Tools

More

Buy/Parametrics

10 results

Include 0 NRND

Part

Show description

Order

CAD Model

Status

Budgetary Price excluding tax

Operating Frequency [Max] (MHz)

Flash (kB)

RAM (kB)

Serial Communication

ADC sample rate

ADC (Channels)

ADC (bits)

Timers

GPIO

Supply Voltage [Min to Max] (V)

Package Type

Package Pitch (mm)

LPC802M001JDH16
Data Sheet

Active

10K @ US$0.47

15

16

2

1 x SPI, 2 x UART

480 Ksps

12

12

1

13

1.71 to 3.6

TSSOP16

0.65

LPC802M001JDH20
Data Sheet

Active

10K @ US$0.50

15

16

2

1 x SPI, 2 x UART

480 Ksps

12

12

1

17

1.71 to 3.6

TSSOP20

0.65

LPC802M001JHI33
Data Sheet

Active

10K @ US$0.54

15

16

2

1 x SPI, 2 x UART

480 Ksps

12

12

1

17

1.71 to 3.6

HVQFN32

0.5

LPC802M011JDH20
Data Sheet

Active

10K @ US$0.52

15

16

2

1 x SPI, 2 x UART

480 Ksps

12

12

1

16

1.71 to 3.6

TSSOP20

0.65

LPC802UK
Data Sheet

Active

10K @ US$0.50

15

16

2

1 x SPI, 2 x UART

480 Ksps

12

12

1

13

1.71 to 3.6

WLCSP16

0.4

LPC804M101JDH20
Data Sheet

Active

10K @ US$0.58

15

32

4

1 x SPI, 2 x UART

480 Ksps

12

12

1

17

1.71 to 3.6

TSSOP20

0.65

LPC804M101JDH24
Data Sheet

Active

10K @ US$0.62

15

32

4

1 x SPI, 2 x UART

480 Ksps

12

12

1

21

1.71 to 3.6

TSSOP24

0.65

LPC804M101JHI33
Data Sheet

Active

10K @ US$0.65

15

32

4

1 x SPI, 2 x UART

480 Ksps

12

12

1

30

1.71 to 3.6

HVQFN32

0.5

LPC804M111JDH24
Data Sheet

Active

10K @ US$0.64

15

32

4

1 x SPI, 2 x UART

480 Ksps

12

12

1

20

1.71 to 3.6

TSSOP24

0.65

LPC804UK
Data Sheet

Active

10K @ US$0.61

15

32

4

1 x SPI, 2 x UART

480 Ksps

12

12

1

17

1.71 to 3.6

WLCSP20

0.4

Documentation

Quick reference to our documentation types.

Filters

1-10 of 41 documents

Compact List

Application Note (19)
Show All

Design Files

Quick reference to our design files types.
Filters

2 design files

Hardware

Quick reference to our board types.
Filters

1-5 of 10 hardware offerings

Show All

Software

Quick reference to our software types.

Filters

1-5 of 8 software files

Show All

Note: For better experience, software downloads are recommended on desktop.

Engineering Services

1-5 of 8 engineering services

Show All

To find additional partner offerings that support this product, visit our Partner Marketplace.

Training

Filters

1-5 of 6 trainings

Show All

Recently viewed products

There are no recently viewed products to display.