Features
Battery Cell Controller, Advanced, 6 Channels, TPL, LQFP48.
Package
HLQFP48 LQFP64, plastic, low profile quad flat package; 64 terminals; 0.5 mm pitch; 10 mm x 10 mm x 1.4 mm body.
Buy Options
PCA9532PW,118
Active
12NC: 935272837118
Details
Order
PCA9532PW,112
End of Life
12NC: 935272837112
Details
Order
PCA9532PW/S908,118
No Longer Manufactured
12NC: 935289587118
Details
Order
Operating Features
| Parameter | Value |
|---|---|
Number of Channels | 16 |
Output Current on pin LEDn (Max) (mA) | 25 |
Supply Voltage [Min to Max] (V) | 2.3 to 5.5 |
Serial Communication | 1 x I²C |
Topology | Voltage switch |
| Parameter | Value |
|---|---|
Blinking Rate (Min to Max) (Hz) | 0.59 to 152 |
# of Addresses | 8 |
Operating Temperature (Min-Max) (℃) | -40 to 85 |
AEC-Q100 compliant | N |
Environmental
| Part/12NC | PbFree | EU RoHS | Halogen Free | RHF Indicator | REACH SVHC | Weight (mg) |
|---|---|---|---|---|---|---|
PCA9532PW,112(935272837112) | Yes | Yes Certificate Of Analysis (CoA) | Yes |  | REACH SVHC | 87.69209766499979 |
PCA9532PW,118(935272837118) | Yes | Yes Certificate Of Analysis (CoA) | Yes | | REACH SVHC | 87.69209766499979 |
PCA9532PW/S908,118(935289587118) | Yes | Yes Certificate Of Analysis (CoA) | Yes | | REACH SVHC | 182.17046399999984 |
Quality
| Part/12NC | Safe Assure Functional Safety | Moisture Sensitivity Level (MSL) | Peak Package Body Temperature (PPT) (C°) | FIT | MTBF | IR | ||
|---|---|---|---|---|---|---|---|---|
| Lead Soldering | Lead Free Soldering | Lead Soldering | Lead Free Soldering | |||||
PCA9532PW,112 (935272837112) | No | 1 | 1 | 240 | 260 | 2.0 | 5.0E8 | 0.0 |
PCA9532PW,118 (935272837118) | No | 1 | 1 | 240 | 260 | 2.0 | 5.0E8 | 0.0 |
PCA9532PW/S908,118 (935289587118) | No | 1 | 1 | 240 | 260 | 2.0 | 5.0E8 | 0.0 |
Shipping
| Part/12NC | Harmonized Tariff (US)Disclaimer |
|---|---|
PCA9532PW,112 (935272837112) | 854239 |
PCA9532PW,118 (935272837118) | 854239 |
PCA9532PW/S908,118 (935289587118) | 854239 |
Discontinued and Replacement Part Data
| Part/12NC | Discontinuance Notice | Last Time Buy Date | Last Time Delivery Date | Replacement |
|---|---|---|---|---|
PCA9532PW/S908,118 (935289587118) | NOTICE | 2020-03-01 | 2020-06-01 | PCA9532PW,118 (935272837118) |
Product Change Notice
| Part/12NC | Issue Date | Effective Date | PCN | Title |
|---|---|---|---|---|
PCA9532PW/S908,118 (935289587118) | 2019-05-30 | 2019-05-31 | 201905028DN | Discontinuation for NXP R01 High Performance Analog and RN3 Secure Interface Devices |
More about PCA9532
The PCA9532 is a 16-bit I²C-bus and SMBus I/O expander optimized for dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB) color mixing and backlight applications.
The PCA9532 contains an internal oscillator with two user programmable blink rates and duty cycles coupled to the output PWM. The LED brightness is controlled by setting the blink rate high enough (> 100 Hz) that the blinking cannot be seen and then using the duty cycle to vary the amount of time the LED is on and thus the average current through the LED.
The initial setup sequence programs the two blink rates/duty cycles for each individual PWM. From then on, only one command from the bus controller is required to turn individual LEDs ON, OFF, BLINK RATE 1 or BLINK RATE 2. Based on the programmed frequency and duty cycle, BLINK RATE 1 and BLINK RATE 2 will cause the LEDs to appear at a different brightness or blink at periods up to 1.69 seconds. The open-drain outputs directly drive the LEDs with maximum output sink current of 25 mA per bit and 200 mA per package (100 mA per octal).
To blink LEDs at periods greater than 1.69 second the bus controller (MCU, MPU, DSP, chipset, etc.) must send repeated commands to turn the LED on and off as is currently done when using normal I/O expanders like the NXP Semiconductors PCF8575 or PCA9555. Any bits not used for controlling the LEDs can be used for General Purpose parallel Input/Output (GPIO) expansion, which provides a simple solution when additional I/O is needed for ACPI power switches, sensors, push-buttons, alarm monitoring, fans, etc.
The active LOW hardware reset pin (RESET) and Power-On Reset (POR) initializes the registers to their default state, all zeroes, causing the bits to be set HIGH (LED off).
Three hardware address pins on the PCA9532 allow eight devices to operate on the same bus.