Beginning of dialog window. Escape will cancel and close the window.
End of dialog window.
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button.
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button.
Video Player is loading.
Current Time 0:00
/
Duration 1:57
Loaded: 0%
0:00
Stream Type LIVE
Remaining Time -1:57
1x
2x
1.75x
1.5x
1.25x
1x, selected
0.75x
0.5x
Chapters
descriptions off, selected
captions settings, opens captions settings dialog
captions off, selected
en (Main), selected
720pHD
540p
Autoselected
This is a modal window.
Beginning of dialog window. Escape will cancel and close the window.
End of dialog window.
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button.
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button.
Please check the new online NFC Antenna Tool
for tag and reader devices.
The PN7462 family consists of 32-bit Arm® Cortex®-M0-based NFC microcontrollers offering high
performance and low power consumption. It has a simple instruction set and memory addressing along with a reduced code
size compared to existing architectures. PN7462 family offers an all-in-one-solution, with features such as NFC,
supporting all NFC Forum modes, microcontroller, optional contact smart card reader, and software in a single chip. It
operates at CPU frequencies of up to 20 MHz.
Class A, B, and C cards can work on 1.8 V, 3 V, and 5 V supply
Specific ISO UART, variable baud rate through frequency or division ratio programming, error management at character level for T = 0, and extra guard time register
DC-to-DC converter for class A support starting at 3 V, and class B support starting at 2.7 V
Thermal and short-circuit protection on contact cards
Automatic activation and deactivation sequence, initiated by software or by hardware in case of short-circuiting, card removal, overheating, and VDD or VDD drop-out
Enhanced ESD protection (< 12 kV)
ISO/IEC 7816 compliant
Compliance with EMV contact protocol specification
Clock generation up to 13.56 MHz
Synchronous card support
Possibility to extend the number of contact interfaces, with the addition of slot extenders such as TDA8026
Integrated ISO/IEC 7816-3&4 UART interface
The PN7462 family offers the possibility to extend the number of contact interfaces available. It uses an I/O auxiliary interface to connect a slot extension (TDA8035 - 1 slot, TDA8020 - 2 slots, and TDA8026 - 5 slots)
Class A (5 V), class B (3 V), and class C (1.8 V) smart card supply
Protection of smart card
Three protected half-duplex bidirectional buffered I/O lines (C4, C7, and C8)
Compliant with ISO/IEC 7816 and EMVCo standards
Integrated contactless interface frontend
High RF output power frontend IC for transfer speed up to 848 kbit/s
NFC IP1 and NFC IP2 support
Full NFC Forum tag support (type 1, type 2, type 3, type 4A, type 4B and type 5)
P2P active and passive, target and initiator
Card emulation ISO14443 type A
ISO/IEC 14443 type A and type B
MIFARE products using Crypto1
ISO/IEC 15693, and ISO/IEC 18000-3 mode 3
Low-power card detection
Dynamic Power Control (DPC)
Adaptive Wave Control (AWC)
Adaptive Range Control (ARC)
Compliance with EMV contactless protocol specification
The CISC TE support NFC-based WLC that allows small batteries, as they can be charged on a regular basis without any mechanical connector. Furthermore, it allows communic...